Swinging Elbows

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Love the accounting of your interesting side effects of magnets in the workshop, Jerry.

Also following along with keen interest. I am now seeing a few places where the magnets might have been a bad idea, but only time will tell!

- Ryan
 
Getting more and more interesting.

Did you use axial or radial porting.

Bogs makes a good point wrt centrifugal force but at the speeds these things run at I don't think its likely to present problems but the advice is well taken - stay out of the firing line.

Those magnets are acursed by evil spirits. I am using some 50x50x15 (industrial robot gripper application) which exert near half a ton at saturation - bloody dangerous - several workshop tools have attacked me.

And like you say stuff in the air sticks to them - even in a food processing (clean) environment I'm finding iron filings accumulating.

Also keep them clear of magnetic memory devices including credit card mag-stripes.

Ken

 
Here it is, running, not perfect, but it is almost the first successful run. It actually ran a few minutes ago but I didn't have the camera set up. At the time of this video, it has actually run about one minute.

http://www.youtube.com/v/8N0Z42wox8c?version=3&hl=en_US&rel=0

Before I quit for the day, it had about 15 minutes of run time and the performance had improved substantially. It self starts reliably and the angle of articulation has increased some. It is terribly inefficient. There are no rings or seals on the pistons, which are 3/8" polished steel shaft running in an aluminum bore, so there is a lot of air leakage, blow by. Without rings or seals, the only way to get any sealing is with a lot of 30wt oil. I am using so much oil that it might be classed as a "hydra-pnuematic" motor. I probably will not do anything to reduce oil flow until I am convinced that the rough edges are worn of and that free oil flow has purged the wear products and any remaining contamination.

The valve is radially ported. I did not show any detail of its design or fabrication because of the huge doubt that this thing would work. Now that it has proved successful, I will show its design if there is an interest.

More testing and reports will follow.

Jerry
 
Remarkable engine :bow: I have little imagination and rely on applying others ideas, so this sort of invention is a wonder for me.

Jan
 
Its Alive !

Well done Captain - Another motor to add to your collection of engines with a high WTF factor.

I like it.

Ken
 
Nice Job Capt!
:bow: :bow:

Definitely classifys as a WTF masterpiece.....I have never seen an engine do that! th_confused0052 th_wtf1

Dave
 
A little backpedaling and I'll show how the valve was made. The main cylinder rotates on cast iron bushings turning on a 1/4" polished steel shaft. The air enters one side of the standard, connects with a passage in the shaft, travels through the shaft to the valve port in the shaft. As the main cylinder block and bushing rotates, a radial hole (one of five) passes over the port and transfers air to the appropriate cylinder to drive the piston. In the second half of rotation, the cylinder port passes over the exhaust port on the shaft and air is exhausted through the shaft and out the other side of the standard.

This is similar to the porting that Ken used in his Six Shooter elbow engine (last months award winner) except that I am using a much smaller diameter shaft and needed a different method of forming the two air passages through the shaft from the standard to the port and a slightly different method of making the port.

The first step is to drill a hole in the end of the shaft. The hole is 7/32" diameter, 1.25" deep was first center drilled and then drilled to full diameter without intermediate sizes. Super high precision is not needed for this hole.

swing004.jpg


The shaft is then extended from the chuck and parted off at a length of 1.5". The shaft is then extended from the chuck for a length of about 2" and turned to 7/32" or to fit hole drilled in the first part.

swing005.jpg


This fit should be close but should not an interference fit. When the thin shell of the first part is fitted over the turned down section of the second part, I don't want it distorted. It will be secured and sealed with locktite but before it is fitted, the air passages must be milled. Out of the lathe and into a V-block in the mill vise.

Two 1/8" wide slots are milled on opposite sides of the shaft. The length of the slots is not critical but it should not extend to the end of the shaft or to the shoulder. The depth of each slot is .062" leaving a web thickness of .126".

swing008.jpg


After the slots are milled, and the edges cleaned up with a file, the locktite is applied to the shaft and then inserted into the shell being careful not to allow sealant into the slots. The shaft is not removed from the V-block during this process so that the position of the slots is retained.

swing010.jpg

swing011.jpg


After the locktite has cured overnight, one hole is drilled through the outer shell to intersect the groove. This hole will match up with the air passage in the standard to allow air into the slot. The port is positioned, according to the dimensions of the standard and the position of the passages in the cylinder block. At this position, the port is mill as a transverse slot to the same depth as the lengthwise slot.

swing012.jpg


The depth of this slot affects the timing of the valve and was worked out using experimentation with an Alibre' solid model. It may not be optimal and may not even work. Actual experimentation will be needed for that answer. If the cross slot is milled too deep, it may weaken the shaft and also may bleed between pressure and exhaust. Too shallow and there may not be enough power.

The same process is carried out on the opposite side of the shaft for exhaust.

I hope this makes sense and is of interest.

Jerry















 

Latest posts

Back
Top