Downsizing...photo intensive

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

RManley

Well-Known Member
Joined
Jan 6, 2011
Messages
113
Reaction score
38
Well, I had to finally bite the bullet and move house. Living in the UK means that finding a house, with a garage or suitably sized garden, is a very expensive proposition and one that I cannot afford. So, I've had to downsize from using my parents garage and garden to building a small workshop in my postage stamp size garden. Sadly I have had to leave allot of my stuff with my parents for safe keeping including my tom senior milling machine :-[

This is why all the projects have come to a sudden stop!
So, here is a small selection of photos of a shed from scratch.

Laying a slab base for my new 10ft x 8ft shed workshop using dry sand and cement (November 2011)
17112011784.jpg


It was cold in January when the shed finally came
14012012845.jpg


Insulating using rock wool (other brands are available), 3/8 chip board will go over the walls.
22012012863.jpg


All insulated and painted ready for my second hand floor tiles. The second door is yet to be done but is on the list.
06032012903.jpg


The big move! Going from a 10ft x 12ft workshop to a 10ft x 8ft is tricky. I had to leave my senior mill behind (temporarily I hope) but managed to pick a decent mill up as a sort of replacement. Can you guess what it is yet?
09032012915.jpg


The main machines are moved into place. its a Raglan mill by the way.
09032012917.jpg


Once the machines were placed, shelves fitted in almost the same place as in the old workshop
11032012922.jpg


A ring main is installed around the shelves and machines. The benches are made from cheapo b&q kitchen worktop on frames screwed to the wall.
03042012934%255B1%255D.jpg


A smaller bench is constructed to mound the pillar drill and tapping machine. Its all a squeeze!
21042012968.jpg


Now that the main bench (approx 2m in length) is fitted, the small vice is fitted and the large vice will be fitted over the led on the end.
21042012964.jpg


The shed is now almost complete. I just have to re-setup the machines to turn true, have no backlash and run quietly. Im currently rubber mounting everything on the mill to make it suitable for urban running.

21042012967.jpg


And all of this I have to share with my motorcycle. With such little space inside, it warms up quickly with bodyheat alone!
21042012970%255B1%255D.jpg


I hope to get some more proper modelling done soon but before I can I have to convert all my milling kit from 1/2" to 3/8" t slots and a few other things. A little bit of a tidy, workout where tools seem to naturally place themselves and It will be like I've never moved.

So, small spaces can be used!

Rob.
 
Great use of a small space, Rob. Looks like a lot of thought and planning went into it. Nice photos too. Thanks for sharing.

Regards,
Rudy
 
looks like a crazy little man cave can you heat it with a light bulbs and coll with the mechanism from a portable electric cooler IIRC a peltier device?
Tin
 
Great job getting all of that gear into your new shed. your top shelf has a bit of a bow in it though. could you fit a bit of timber under it or another bracket to shore it up?
 
Just for your amusement, I have attached the photo below. The shelf has permanently deformed....I couldn't straighten it without fear of snapping in! So, I have reduced the load by half and screwed a small block to the wall so It wont sag any more, hopefully!

11032012920.jpg


A crazy little man cave it certainly is! I escape to it when the missus is watching soaps on the TV. It is s well insulated that after 5 mins of having 1 light on and using a machine i'm plenty warm enough. I Just hope that I have used sufficiently beefy enough cable in the ring main and its not that glowing red and warming the shed!

panofish, I had a look at your baby, very nice indeed! They are so easy to work on and tinker with, more like a kit bike than anything else. A little tip, dont keep the bike in the shed whilst the fresh emulsion (water based) is drying - it makes the chain and other steel parts go rusty!

Rob.
 
Turn it upside down and load it! If you do, it will take the load and straighten itself out, at least some of the way.
 
Nice one. The thought of having to pick the contents of those drawers out of your lathe and off the bench and floor had me nervous on your behalf. Well done on such a great piece of effective space use. Getting the bike in there too is most impressive. A perfect escape from the soapies on tele.
 

Latest posts

Back
Top