Siege Super X3 Mill mods

Advertise with us
Shop deals on ebay
Find deals on amazon
Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
G

geoffh

Guest
Hi All,
I have acquired one of these mills via father Christmas, and very pleased I am with it all but for 2 points.
1) The Z axis requires a lot of manual turning to raise and lower the head and it seems to me that to motorise the Z axis would be a very beneficial improvement. Does anybody know of a kit or someone who has done this conversion and would be prepared to help me?
2) The table cross travel is proving difficult to adjust to point of no play without sticking, it seems the vee grove on the carriage may not be parallel. Has anyone else experienced this?
Cheers Geoff
 
I built this counterweight system for my X3 which greatly reduces the effort needed to raise & lower the head. I also chucked a 14mm socket in an old Makita cordless drill and use it to spin the Z handle to quickly raise & lower the head. Much easier on the shoulder!:)

counterweightsm.jpg
 
Hi Dickeybird,
Thanks for the reply.
An ingenious solution. I was hoping someone in the forum had done this mod with a stepper motor and controller, similar to the one done for the x travel. Did you have trouble adjusting the y axis gib strips to give you a smooth movement with no stcking or play.
Regards Geoff
 
Geoff
I have not had the problem with the Y axis. In fact the only minor lash problem here is with my X axis. Both have split nuts on the lead screws with adjustments, but they are difficult to reach without removing the table.

Here is one man's solution to motorizing the Z axis along with a couple of other mods he's come up with.

http://www.viddler.com/explore/rashid11/videos/4/

Steve
 
Hi Steve,
Thanks for the reply. A very useful and helpful video. I have just started my Hobie and there is so much to learn. He is on the right lines with respect to what I want to do with the Z axis and given me some ideas. I would like to do something with more control hence the stepper motor and controller approach (I have no experience). I know I can get stepper motors off the shelf but getting a ready made controller or the plans to build one is my problem. Any ideas.
Thanks again.
Geoff
By the what I have been very carefully dressing the Y axis vee groove on the carrage and have improved the situation somewhat.
 
Hi Rich,
Thanks for the reply. This is precisely what I am looking for but modified to suit the Z axis. How do I contact Julian and would he sell me the circuit diagram + parts info?
Cheers Geoff
 
Hi Geoff

Post the question in the motorised mill topic or send him a pm. Be patient for a reply though he works long shifts.

Cheers

Rich
 
I recall seeing a simple but effective method of locking the spline shaft when changing collets..I have skinned too many knuckles using the 2 pin spanner that came with the Mill
does anyone have a solution that is simple??
Thanks
joebiplane
 
joebiplane said:
I recall seeing a simple but effective method of locking the spline shaft when changing collets..I have skinned too many knuckles using the 2 pin spanner that came with the Mill
does anyone have a solution that is simple??
Thanks
joebiplane
Click to expand...

I just use a Adjustable Pin Spanner Wrench. I just hook it on the splins and use a wrench to tighten or loosen the draw bar. So far no damage to the splined shaft.
 
Hi,
I have had an X3 for about 7 years. Been a good little mill so far. The first and only thing I modified was a spindle locking device for changing tools. My locking device is simple. It is a brass plunger with a retracting spring and a mushroom head on the outside. It is located on the front of the top gear cover. By pressing on the mushroom button with the palm of your left hand, the plunger is jammed between two teeth of top spindle gear, and locks the spindle as long as pressure is firmly applied to the mushroom button. That leaves the right hand available for tightening or loosening the drawbar bolt. It has worked well for 7 years and doesn't harm the gear. It took me about an hour to complete once I found the right spring.

I replaced one air spring. It lasted another year. I have done fine without the air spring. Just takes a little cranking and keeps my right arm in shape. Still less effort than my friend's Bridgeport.

The only problem I am having now is a grabbing action on the ways when making fine movements. I ran out of the old way oil and the problem started after I began using a new way oil. Wish I could remember what the old oil brand was.

Jeff
 
Jeff,
Got a picture or sketch of your locking device...I have a lot of sore knuckles
Thaanks
Joebiplane
 
Hi to all who post on "Siege Super X3 Mill mods"

Can I add a small tip. Use "Cup Point" grub screws for gib adjustment and a "Ball Bearing" that is "Tapping Size" for the Gib Screw I.E 6 mm thread 5 mm ball bearing.

Also Use "Chainsaw Bar Oil" on Gibs it's cheap it's tacky and is used by lots of machinists.

See "Lucky Accident" posted in "Machine Modifications".

Eric
 
Joebiplane,
Here are the only photo's I have of my X3 spindle locking modification. That's the underside of the gearbox top cover. The spindle projects out the top of the gearbox through the large hole shown. This spindle lock is quicker and easier to use that the lock on a Bridgeport spindle.

Jeff

X3-3.jpg


X3-4.jpg
 
The first thing I noticed when I started using my Grizzly G0619 (Sieg SX3) mill
was that it was awkward and time consuming changing tools with the supplied pin
spanner wrench. So I created a new tool called the Spindle Brake.

The Spindle Brake replaces the supplied pin spanner wrench and makes tool
changes quick, easy, and safe saving time and increasing productivity.

I enjoy using my Spindle Brake every day. Please go to www.PriestTools.com to
see and purchase the Spindle Brake.

_MG_3904.jpg


_MG_3918.jpg


X3-top-7.jpg
 
You must log in or register to reply here.

Similar threads

B
Question Re: Sieg SX2.7 Mill
Replies
2
Views
5K
blanik
B
deeferdog
Z axis motorisation GO704 mill (Optimum BF-20LV)
Replies
2
Views
3K
Wizard69
W
D
Seeking Sieg X3 DRO info please
2
Replies
26
Views
15K
Pete.
P
R
A Kimble Engine
Replies
5
Views
8K
romartin
R
docwatson
Sieg X2 clone mill in UK, first impressions...
2
Replies
24
Views
17K
docwatson
docwatson

Latest posts

Back
Top