Help Support Home Model Engine Machinist Forum:

Olli-Matti

HMEM Supporting Member

Well-Known Member 40 From Espoo, Finland

Joined: Apr 29, 2020

Last seen: Yesterday at 8:56 AM

Latest activity Postings Media About

- O
  
  Olli-Matti reacted to minh-thanh's post in the thread Antares 2cc - model diesel engine build with Like.
  
  Nice engine , Congratulations ! Thanks for sharing.
  
  May 28, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Got the last part of the Antares build videos out. Check it out here:
  
  May 27, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Antares 2cc popping on ether
  
  May 17, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Conrod is now done aswell as the wristpin. Started lapping the piston. Not much left before the final assembly.
  
  May 16, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Thanks K2! I think your numbers are very close as I did infact take only 0.05mm passes and a double pass every here and there because of...
  
  May 11, 2023
- O
  
  Olli-Matti reacted to John Shannon's post in the thread Antares 2cc - model diesel engine build with Like.
  
  Olli, That is really nice looking! Turning "backwards" has many uses. Johnny
  
  May 8, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Finally done with the compression screw. Finished the contour with an angle grinder, rotary tool and assortment of files. Still needs...
  
  May 8, 2023
- O
  
  Olli-Matti reacted to rklopp's post in the thread Antares 2cc - model diesel engine build with Like.
  
  Olli, That is some very nice work. There's a lot interesting techniques to learn. I note the chucking spud and "backward" boring bar...
  
  May 8, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Thanks Andrew, Mitutoyo is always a mituotoyo 😉 I have Carl-Zeiss Jena comparator for 10-18mm and CCCP one fpr 6-10mm. I did end up...
  
  May 7, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  The cooling jacket is done. Had to use some artistic freedom as I still dont have ability nor skill to grind tools and had only 1.5mm...
  
  May 6, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Adventures with the cylinder. A lot of work fitting it properly to the case. Also had lot of trouble with the cyl thread but managed to...
  
  May 2, 2023
- O
  
  Olli-Matti replied to the thread BollAero18 2021 Build.
  
  Thanks for sharing, it looks just fine, too bad it hasn' ran yet. Have you seen this article on making the piston fit to cylinder? If...
  
  Apr 30, 2023
- O
  
  Olli-Matti reacted to John Shannon's post in the thread Antares 2cc - model diesel engine build with Like.
  
  This is the .stl file with machining stock added. It printed on my cheap printer in PLA, but could not finish because I don't know how...
  
  Apr 29, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Spinner and fuel line out of the works today.
  
  Apr 28, 2023
- O
  
  Olli-Matti replied to the thread Antares 2cc - model diesel engine build.
  
  Milled the inlet port to the carb and installed the carburetor body to the case. Took quite a bit of fiddling again to get the needle...
  
  Apr 28, 2023
Show older items
Loading…
Loading…
Loading…