Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

trlvn
Reaction score
41

Latest activity Postings About

    • trlvn
      trlvn replied to the thread Press Fits.
      That is a beautiful tool set but the minimum size it will measure is 0.8 inches. The OP's application was a 5/8" hole. Craig
    • trlvn
      trlvn reacted to ajoeiam's post in the thread Press Fits with Like Like.
      Hmmmmmmm - - - - methinks it is not so much 'easier' as it is possible. Using telescopic gauges - - - I'd be willing to bet that the...
    • trlvn
      trlvn reacted to Steamchick's post in the thread Press Fits with Like Like.
      As I use a Vernier Caliper that is repeatable to 0.002" (Not a digital caliper!), and my MODEL workshop is about capable of the same...
    • trlvn
      trlvn replied to the thread Press Fits.
      Supposing a '5/8 inch' hole, how does one measure it with tenths accuracy (0.0001")? Can you get gauge pins in increments of a tenth...
    • trlvn
      trlvn reacted to awake's post in the thread Need advice on bench grinder wheels with Like Like.
      The key parameter that I look for is the hardness of the wheel. Counter-intuitively, the harder the steel, the softer the wheel needed...
    • trlvn
      trlvn reacted to Brian Rupnow's post in the thread Taking it up a step--- with Like Like.
      And today I have reached part #2 of "Taking it up a step". This is an inside micrometer which will measure from 1" to 2" inside...
    • trlvn
      trlvn reacted to terryd's post in the thread Taking it up a step--- with Like Like.
      Hi mike, I have 2 almost identical inexpensive digital calipers which I purchased at more or less the same time. One retains it's...
    • trlvn
      I LIED!!! I wanted to see what effect heavier flywheels would have, but didn't want to make new flywheels. I got digging around in that...
    • trlvn
      Cameron micro drill press model 164D-7, 2 speed motor and 3 pulleys, depth stop, Albrecht 1/16 inch chuck. A good friend of mine who...
    • trlvn
      trlvn reacted to clockworkcheval's post in the thread Taking it up a step--- with Like Like.
      Hi Brian, your planned micrometer additions sound useful. Perhaps it comes with old age, but I found myself mis-reading micrometers...
    • trlvn
      trlvn reacted to Brian Rupnow's post in the thread Taking it up a step--- with Like Like.
      TRLVN--Getting one like the center picture.---Brian
    • trlvn
      trlvn replied to the thread Taking it up a step---.
      What device are you getting, exactly? A 3-prong hole micrometer? A 2-pin mic that can measure on the inside or outside? Or a...
    • trlvn
      trlvn reacted to krypto's post in the thread Cut Off Saw & Gear Cutting Arbors with Like Like.
      Years ago I bought a few lots of used/NOS USA slitting saws and made 1/2" & 5/8" arbors to drive them. As Ninefinger mentioned, the very...
    • trlvn
      trlvn reacted to Steamchick's post in the thread Wanted Casting Kits with Like Like.
      Hi Fireguy. - KJ. I hope the weather in Buffalo has improved. Sorry, I do not have any spare kits for sale, but can advise UK regular...
    • trlvn
      trlvn reacted to Joe's post in the thread Wanted Casting Kits with Like Like.
      KJ, re. the Blondihacks video, Joe Pi did that engine too. Two different creators, two different approaches. BH is hobbyists, "this...
  • Loading…
  • Loading…
Top