Search results

I've bought boring bars, parting tools and numerous 1/2" shanked turning/facing tool sets from Banggood, the quality has been surprising good and the inserts are more than compressed dirt. The only downside to some people, is the delivery time, I've gotten packages in 6 days and others in 3-4...

I've been reading this thread with great interest, I bought on of the tangential tools, from Australia, through the US rep, Village Press. After seeing rave reviews, in a few magazines and on some of the forums, it now sets unused in the bottom of the lathe tool drawer. I tried it with HSS and...

John, You posted on Shopfloortalk, a while back about the swing up threading tool I made using an AXA, QCTP block and a carbide insert threading tool from Grizzly Industrial. I had somewhat copied your design, I had seen it some where in the forums, it works great. Thanks for sharing that.

too bad were so far apart, I got 30-35 gallons of Mobil Vactra 2 wayoil in shop storage, I'd be more than glad to give you some.

The Aloris 16 (I have one) is not a great, but is an expensive tool, while using cheap inserts (TPG/TPU 321/322), the finish quality is below average. You would be better off using tooling that uses CCMT inserts.

I use .020" Teflon gaskets to seal up high pressure steam boilers, running at 230 psi, with no issues.

I did somewhat of a similar thing, I used a magnetic Cedarburg coolant base and the Line-Loc interlocking coolant lines, with a small regulator. I set it at just enough air flow to keep the chips moving away from the cutter. Attached is a picture of the unit, but not in use.

I put a one shot system on my 1938 Bridgeport milling machine, I bought the Enco pump, then made the orifices based on the size for the new milling machines. I threaded the elbow fitting and put an aluminum set screw in the fittings, the drilled the set screws to the needed sizes, then check the...

I did mine last week, used a piece of 7/16"-20, B-7 hardened all-thread and pinned and then plugwelded a coupling nut to. Works perfectly, short one is for mill/drill and longer one is for the Jet mill.

I just installed one on my Jet JVM 836 mill, so far so good Jack

I open them up all of the time for a customer, they run an AXA size tool posts on a paper machine, they hold slitting knives, that have 19 mm shanks. I done probably about 25 of them, they have them preset with new sharp knives, and can change them on the fly. I use a 1/2" 4 fl carbide end mill...

This project is moving right along, much faster than I originally thought. With the jib modified and welded in lifting eye, all assembled, its time to consider the lifting device to pick up the RT and the chuck, when needed. I was looking for a small chain fall or small electric lift, then...

9 - ring 10 - the ring welded into the shortened sliding arm 11 - set at min setting 12 - max setting

5 - crane kit 6 - post mounted 7 - checking clearances 8 - preliminary assembly jack

I'm getting to the age (55 this month) that lifting a 10" rotary table and the 10" chuck up on the mill table is getting harder and harder everytime. After much searching, looking and even more procrastinating I started a jib crane to do the lifting. I made a mounting pad to go on the...

5 - top of baffles 6 - bottom of baffle 7 - close fit of baffle to tube body 8 - both mounted, ready to use The driers are piped with new Apollo ball valves and air line quick-connects, to allow quick change over. jack

I just bought the Harbor Freight model #97686 desiccant air drier, $40, that uses #97924 desiccant media, $5 for 2.2# (1 kilo). Its a 34" long piece of 2" pipe, it has 2 screw on caps and 2 media support baffles. When assembled there is about 24" of desiccant supported in a vertically mounted...

When I bought my Jet JVM-836 milling machine, I was very happy with the machine, the only drawback was the unit only has 5 spindle speeds (240-1550 rpm). Only 5 speeds and wide gaps between them, was somewhat limiting. I ended up making a "transmission", adding another set of pulleys and a...

When in school, I had to do a oral report on the duckbilled platypus, about a week before I got hit in the mouth with a baseball bat, and lost or broke about 11 teeth. What followed was about 7 months of dental hell to try to get a set of teeth back in there and functioning. I could barely talk...

My name is Jack, I live in central NY state, near Syracuse. For 30+ years, I've been an industrial boiler service technician, at one time traveling the world working on boilers, now concentrating on the northeastern part of the country. I have a machine shop in the garage, and make obsolete...