Search results

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. weez

    Setting up Shop Questions - from an NZ learner

    I think that the videos that Rod is referring to are found here. http://techtv.mit.edu/collections/ehs-videos/videos I watched all of these when I first started machining and found them very informative.
  2. weez

    Hey there

    A simple steam engine is a good place to start. A bunch of plans for Elmer's engines can be found at http://www.john-tom.com/html/ElmersEngines.html. The #25 wobbler is the simplest.
  3. weez

    Elmer's Beam #24

    Here is my completed Elmer's Beam engine. I built this last winter but never got around to posting it. I decided to go with a curved spoke flywheel which I think turned out pretty good. https://www.youtube.com/watch?v=C6SzkT1paxQ
  4. weez

    Looking for an easy hit and miss

    My suggestion would be the Kerzel Hit and Miss engine. It was my first I.C. engine and I didn't find anything to be overly complicated. My build log for this engine can be found here. Brian Rupnow has also done an excellent build log found here.
  5. weez

    Anyone built the Kerzel or Webster engine?

    I also debated between the Webster and Kerzel for my first I.C. engine. I chose the Kerzel because it looks more like a real engine compared to the Webster. I am sure that the Webster is easier to build, but I didn't find anything too difficult about the Kerzel. The build log for my Kerzel...
  6. weez

    First build - Which engine is the best?

    This looks like Jan Ridders Two Stroke Debbie. You can email Jan and he will send you the plans.
  7. weez

    First build - Which engine is the best?

    Check out Elmer's engines found here. There are many different designs to choose from. With your machining experience, I am sure you wouldn't have too much difficulty with any of them. I have built the Wobbler, Standby, Grasshopper, Twin Vertical Wobbler, Comber Rotary, and Geared. I am...
  8. weez

    Blueprint help

    Here are the meanings of the circled letters that Elmer uses. I also made a Comber. The build log can be found here. Good luck with your build. I look forward to seeing it.
  9. weez

    Quick Hello

    Neil, welcome to the forum. If I remember correctly, Steve has stated that his Demon V8 can be completed with manual machines. I have a set of plans and looking through them I do not see anything that is impossible without CNC. I too am planing on making the V8 someday and I am debating...
  10. weez

    Request for engine plan suggestions

    In my opinion the best place to start would be with some of Elmer's engines. Plans can be found here. The simplest one to start with is the #25 wobbler. They are all made from bar stock and there are many different types to choose from. Probably the best first IC engine is the Webster...
  11. weez

    Kerzel Hit and Miss

    After about 220 hours of work over the past 11 months, I have completed my build of Kerzel's Hit and Miss. This was my first IC engine and I am very pleased with how it turned out. The build log can be found here. https://www.youtube.com/watch?v=F_GUp5UXmxE
  12. weez

    Kerzel Hit and Miss

    After about 220 hours of work over the past 11 months, I have completed my build of Kerzel's Hit and Miss. This was my first IC engine and I am very pleased with how it turned out. https://www.youtube.com/watch?v=F_GUp5UXmxE
  13. weez

    Kerzel Hit and Miss

    And now the gas tank. I cut a length of 1" copper pipe and faced off both ends. I did not have any large enough round stock so I had to make the ends of the tank out of 1/4" by 1 1/2" rectangular bar. I turned a small boss that fits inside the pipe. Then soldered on the end cap, trimmed off...
  14. weez

    Kerzel Hit and Miss

    Here are the gas tank mounts. The gas tank will be made of a 2" length of copper pipe. First in the mill I drill a 1/2" hole in the center and two 1/4" holes that will make up the inner radius of the bottom of the mount. Then into the 4 jaw chuck on the lathe centered on the 1/2" hole. I...
  15. weez

    Kerzel Hit and Miss

    Now for the muffler. First turn out half of the profile and drill a hole part way through. After parting off, I flipped it around and turned the other half. Then with the rotary table on the mill I drilled ten 1/16" holes around half of the perimeter. Here is the finish muffler along with...
  16. weez

    Kerzel Hit and Miss

    Thank you everyone for the compliments. Simon and xpylonracer, I am glad I motivated you to continue with your projects. I still need to make the gas tank and a base for it. I am not going to paint it other than maybe painting the spokes of the flywheels.
  17. weez

    Kerzel Hit and Miss

    Have not updated the thread for a while but I have been working on the engine. I finished up all of the governor parts. Here is the video of it running on hit and miss. https://www.youtube.com/watch?v=4iRqz91L5Is
  18. weez

    Another Poppin project.

    See this post for an explanation on how to add pictures within the text. Good work so far on the Poppin.
  19. weez

    Kerzel Hit and Miss

    Thank you Brian for the compliment. After making a few of Elmer's engines with quite tiny steam valve pieces, most of these pieces actually seem fairly large to me. Its funny on how one's perspective can change. Before I got into model engineering about two years ago, I had never seen a screw...
  20. weez

    Kerzel Hit and Miss

    Here are the weights. First drilled the holes for the pins that the springs connect to in the top and bottom of a piece of brass large enough for both weights. Then drill/countersink the mounting holes. I also center drilled the center of the piece. After screwing it to a chunk of aluminum...
Back
Top