How Do I Remove Soft Solder from Brass Surface?

Find deals on amazon
Shop deals on ebay
Advertise with us
Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
4

4156df

Project of the Month Winner!!!
Project of the Month Winner
Joined
Feb 25, 2008
Messages
464
Reaction score
5
I've got a thread going on "Building Rudy's Steam Tractor", but thought I'd ask this here because the answers might be of more general interest.

Some time back, I built the steam box door for my tractor and used soft solder to fasten the faux hinges and lock down bolts. I wasn't concerned about the solder overflow at the time because I planned to paint the door and the paint would cover it. Since then I've changed my mind and would like to leave the door in brass. Does anyone have an idea on how I can remove the solder overflow without damaging or defacing the underlying surfaces? I'd like to keep the fine concentric tooling rings if possible.
P1040099.jpg


Thanks for any ideas.
Dennis
 
I don't know how well this will work but you could try solder wick and a pencil soldering iron.
 
I think you have to scrape it off. Looking at the picture, it shouldn't be so difficult.
 
yes carefully scrape then wire bush a pencil line can keep it from running in the foirst place but looks like you did a neat job of it.
Tin
 
A fine bead blast will erase all of the solder.

Tony
 
Nice question!
I'm going to be interested in seeing the successful results and how you got them.
 

How about an Air Eraser Kit $20 could do the job!!
not the end of the world if it does not work but think it would .
Tin
 
Thanks for the info, guys. The simple soda blaster is one I'll file for future reference.

A couple of you mentioned scraping. Do I use an X-acto knife as a tool or is there more to it?

Tin, I've got one of those air erasers but only have aluminum oxide media. I was hesitant to use it because I thought it would wipe out the fine ring detail. That may be something I have to live with. I'll borrow some glass bead media tomorrow and give it a try.

I think I'll make up a test sample and try both scraping & blasting and go from there. I'll report back.

Thanks,
Dennis
 
Hi Dennis,
I lightly scrape with an Exacto knife with the tip blunted off a little. If you leave it sharp it will put scratches into the work. I then use a little stainless wire brush, the one with the bristles sticking out of the end for rotary tools, and mount it in a small pin vise or drill chuck. Lightly brush by hand and it will get rid of most of it. You won't be able to remove all of it without some very diligent work.
George
 
Try remove main part of soft solder by mechanical tool (knife, Deremel high speed mini grinder). Use smal sand blaster locally at next to remove rest of the solder. And normal sand blaster at the end to homogenize surface. Yhe surface will be clear but matt (sand blasted). It looks good too. It looks as true cast.

And for future you should use silver solder. If you use a very small piece silver solder, it goes into gap after heating and after cleaning in 10% sulfur acid you will see nothing. Ehm, you will see perfect thing ;D.
 
Dennis, if you decide to blast it, use good automotive masking tape to mask everything but the solder over flow. It will protect all your nice edges.
I've watched glass etching done this way, and it keeps the media from etching anyplace other than where the operator wanted it.

Dean
 
You must log in or register to reply here.

Similar threads

B
Help, how on earth do I build the boiler for my Fire King?
Replies
0
Views
1K
Bob Wild
B
R
How can I find a good home for my father's steam engine
2
Replies
22
Views
5K
ACHiPo
ACHiPo
G
How do I join the edges of a brass frame?
Replies
12
Views
5K
Wizard69
W
T
Glass bead finishing ......
Replies
10
Views
5K
toolznthings
T
R
Stuart Twin Launch
Replies
5
Views
9K
Richard Horne
R

Latest posts

Back
Top