Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Forums
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Help Support Home Model Engine Machinist Forum:
K
kwoodhands
HMEM Supporting Member
Well-Known Member
·
79
·
From
mays landing NJ.
Joined
Jan 4, 2010
Last seen
Sunday at 11:14 PM
Messages
220
Reaction score
61
Find
Find content
Find all content by kwoodhands
Find all threads by kwoodhands
Latest activity
Postings
About
K
kwoodhands
replied to the thread
What is it?
.
I have seen these before. Grandfather used them in different ways. Short ones used to set up sine bar. Thread was 64 tpi or so. Also...
Thursday at 6:53 PM
K
kwoodhands
reacted to
djc's post
in the thread
turning a square part to small for the chuck
with
Like
.
If you have some excess of the 1/8" stock, cut off four lengths and superglue them to the faces of the piece you want to use. It then...
Sep 7, 2023
K
kwoodhands
replied to the thread
turning a square part to small for the chuck
.
Thanks for all the replies. I tried it my way and it worked out perfectly. I added a 3/48 screw to the two pieces to hold them together...
Aug 30, 2023
K
kwoodhands
posted the thread
turning a square part to small for the chuck
in
General Engine Discussion
.
I need to thread a 2/56 thread on a 1/8" square part. My chuck will not close tight enough. I do not have collets at this time. I think...
Aug 28, 2023
K
kwoodhands
reacted to
Steamchick's post
in the thread
Changing Lathe
with
Like
.
Better not to try and determine "life expectancy" of people. My mother's heart specialist told her (at 81) that if she had a quadruple...
Aug 16, 2023
K
kwoodhands
reacted to
Henry K's post
in the thread
Changing Lathe
with
Like
.
I must be missing something. Your wife wants you to downsize your lathe for health reasons? You only need to turn wheels to operate the...
Aug 16, 2023
K
kwoodhands
reacted to
Mike N's post
in the thread
1/3 Scale Case Steam engine
with
Like
.
I have been working on my 1/3rd Scale Case Steam Engine. http://youtu.be/SK-7x34rXBg 1915 65HP Case 24: rear wheels Approx.78" Long
Aug 7, 2023
K
kwoodhands
replied to the thread
1916 65 HP Case Traction Engine 1/16 Scale
.
Next time use "white out" to stop the flow of solder. This is the stuff used to erase typos. Looks like white paint. Comes with a small...
Jul 31, 2023
K
kwoodhands
reacted to
Lloyd-ss's post
in the thread
Harbor Freight / Rong Fu Improvements (HF #33686 Round Column)
with
Like
.
It is mixed bag at HF, always buyer beware. But the quality is definitely improving. 2 products I have purchased in the last few years I...
Jul 23, 2023
K
kwoodhands
replied to the thread
Round Column Mill
.
Remove both bolts and check for interference in the yoke gap. Replace the bolts and use a longer wrench to tighten the bolts. I use a...
Jul 22, 2023
K
kwoodhands
replied to the thread
Round Column Mill
.
I use a rotary table for bolt circles. mike
Jul 16, 2023
K
kwoodhands
replied to the thread
Round Column Mill
.
I have a round column mill. When adjusting the height the accuracy is lost. No problem, Install a point or a wiggler and re-position the...
Jul 13, 2023
Loading…
Loading…
Forums
Members
Top