Search results

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. C

    Model engine CDI easy and cheap

    It’s a good solution, All car petrol engines use these now, you can get them for pennies second hand. Also for the signal you can use 12v no issues as it’s just a logic signal, which makes the wiring even easier. I use mine with points on one engine and a magnetic Reed switch on another. Very...
  2. C

    Model engine CDI easy and cheap

    I just use an automotive COP, one thing does whole job, hall sensor triggered, easy to wire up and cheap.
  3. C

    Mini diesel engine.

    A gauge is a gauge, as long as the range is correct it will work fine.
  4. C

    Mini diesel engine.

    If it runs I’ll be delighted 😁
  5. C

    Mini diesel engine.

    I will do, I don’t have the time or inclination for a full thread, but will certainly highlight any new breakthroughs.
  6. C

    Mini diesel engine.

    No leaks at all so far, the screwed connections were surprisingly easy to make successfully. It will hold 40 bar (500psi) for several seconds too, which is promising. I will focus my efforts on a 40 bar injector and then the engine itself now.
  7. C

    Mini diesel engine.

    Thanks, I think it will be adequate, I will now continue work on my engine and try complete the project in 2022…. As for gauges this was surplus’s from a job at work, but something off eBay would do? I don’t think you will need one above 100 bar… but you never know!
  8. C

    Honda GX160- 8.5cc

    Looks good!
  9. C

    Mini diesel engine.

    I have done some maths and I think 40 bar injection pressure will work with 45 degrees injection timing. Cylinder pressure at that point will not be high. The injector should withstand 650bar cylinder pressure with that spring too, assume 8kg spring and the size nozzle I am running.
  10. C

    Mini diesel engine.

    https://youtube.com/shorts/_fTypyV3I-o?feature=share
  11. C

    Mini diesel engine.

    Some success with the “old” style injection pump, Minh-Thanh what injection pressure does your injection pump achieve? What pressure are you popping your injector at? Chaffe
  12. C

    Mini diesel engine.

    Simple answer is heat, heat is lost to the cylinder walls, piston, head and the fuel. The smaller the cylinder the less heat energy you will get from the air charge. Physics don’t scale very well, especially when it comes to thermal dynamics.
  13. C

    Honda GX160- 8.5cc

    lovely job! this engine is the pinnacle of small petrol engines, a modern classic. Look forward to the finished article.
  14. C

    Mini diesel engine.

    Hi, I have what I consider to be quite a good bore (size and finish) in my cast iron pump, the piston was in fact not machined and I tried to use ground stainless bar, it is too small… I’ll make a piston when time permits. The check valves seem to be the real test for me 😂 I will try a tapered...
  15. C

    Mini diesel engine.

    You’ll not get emery or scotchbrite in a 2mm hole, 11mm deep…. ideally I would want to polish it with a ball soldered onto a brass rod, with compound. I believe the new design with a 30 degree seat and slightly larger ball will be better.
  16. C

    Mini diesel engine.

    The brass fitting above is in fact my delivery check valve, it’s m5/m6 so you can appreciate the size. The ball is 2mm and is some 11mm deep to the seat, there is also a spring and retaining collar inside. I am not sure how you would polish such a seat so deep?
  17. C

    Mini diesel engine.

    Only the photos I posted a few posts ago. I am treating the engine and injection system as two separate things. I think the engine it’s self will be an easy task.
  18. C

    Mini diesel engine.

    Thanks guys, I have finished my steam engine project, now I have spent some time on my new injector pump. Cast iron body with steel piston, still need to refine the piston as it has some leakage, but looking promising. I have a question, my delivery check valve doesn’t seal (ball and spring...
  19. C

    Mini diesel engine.

    Thanks, my next plan was exactly as you describe, using cast iron for cylinder and silver steel as piston, a split aluminium lap. but first I must finish my Stuart steam engine…
Back
Top