My first home made model engine The Boll Aero 1,8

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Hallo Model Engine Friends

I have done another modification at my Boll Aero 1.8 model engine.
I made a new piece of screwthread at front of my Crankshaft and used for it an
adjustment Bolt M5 x 40 mm!
You can see the final results on te photos i send with this reply message.
I hope you like the final result.

many greetings from modelmotor-Gerard-The Netherlands-Europe.

Boll Aero 1.8 cc model diesel engine  update 031.jpg


Boll Aero 1.8 cc model diesel engine  update 032.jpg


Boll Aero 1.8 cc model diesel engine  update 033.jpg


Boll Aero 1.8 cc model diesel engine  update 034.jpg


Boll Aero 1.8 cc model diesel engine  update 035.jpg


Boll Aero 1.8 cc model diesel engine  update 036.jpg


Boll Aero 1.8 cc model diesel engine  update 037.jpg


Boll Aero 1.8 cc model diesel engine  update 038.jpg


Boll Aero 1.8 cc model diesel engine  update 040.jpg
 
G'day Modelmotor
After looking at the photo's of your crankshaft with the undercut section of the shaft adjacent to the intake port on the shaft I would be very interested to know how well your motor runs.
Because by machining away what looks to be, between .010" to .020" off the diameter of the shaft the seal between the shaft and the crankcase is now non existent, meaning the port can never truly open or close, so that the port in the shaft is always open and you will be loosing crankcase pressure all the time.
Also you would be better tapping the shaft in the lathe between the chuck and the tailstock for alignment.
Rob Jenkins.
 
G'day Modelmotor
After looking at the photo's of your crankshaft with the undercut section of the shaft adjacent to the intake port on the shaft I would be very interested to know how well your motor runs.

Rob Jenkins, it's not intake port. Also to lubricate the bearing via canal from crankcase to bearing. The engine is a side port engine.
 
Hallo Model Engine Friends,

I have found several small issues which needed an update at my first made Boll Aero 1.8 cc.This engine built in 2008 without any knowledge about about home made model engines diserves a good tune up i think.
I made a photo collage from all the parts i renewed or made from new material.
I hope that you enjoy the photos as much as i did.

many greetings from modelmotor-Gerard-The Netherlands-Europe.

update several Boll Aero engine parts 003.jpg


update several Boll Aero engine parts 005.jpg


update several Boll Aero engine parts 006.jpg


update several Boll Aero engine parts 010.jpg


update several Boll Aero engine parts 011.jpg


update several Boll Aero engine parts 013.jpg


update several Boll Aero engine parts 014.jpg


update several Boll Aero engine parts 015.jpg


update several Boll Aero engine parts 016.jpg


update several Boll Aero engine parts 017.jpg


update several Boll Aero engine parts 019.jpg


update several Boll Aero engine parts 021.jpg


update several Boll Aero engine parts 022.jpg


update several Boll Aero engine parts 025.jpg
 
Hallo Model Engine Friends,
I had left some pictures from updates done at my Boll Aero engine recently and in the past.
I hope that you enjoy the pictures from the updates just like i do.

many greetings from modelmotor-Gerard-The Netherlands-Europe.

update several Boll Aero engine parts 026.jpg


update several Boll Aero engine parts 028.jpg


update several Boll Aero engine parts 029.jpg


update several Boll Aero engine parts 030.jpg


update several Boll Aero engine parts 031.jpg


update several Boll Aero engine parts 034.jpg


update several Boll Aero engine parts 035.jpg


update several Boll Aero engine parts 038.jpg


update several Boll Aero engine parts 042.jpg


update several Boll Aero engine parts 045.jpg


update several Boll Aero engine parts 046.jpg


update several Boll Aero engine parts 050.jpg


update several Boll Aero engine parts 051.jpg
 
Hallo Model Engine Friends,

Here are my last pictures made after my last Boll Aero engine updates.
I hope you had a good time watching the pictures from my home made model engine "the Boll Aero 1.8 cc".
Many greetings from modelmotor-Gerard-The Netherlands-Europe.

continuering update Boll Aero 1.8 cc 002.jpg


continuering update Boll Aero 1.8 cc 003.jpg


continuering update Boll Aero 1.8 cc 004.jpg


continuering update Boll Aero 1.8 cc 005.jpg


continuering update Boll Aero 1.8 cc 006.jpg


continuering update Boll Aero 1.8 cc 008.jpg


continuering update Boll Aero 1.8 cc 009.jpg


continuering update Boll Aero 1.8 cc 011.jpg


continuering update Boll Aero 1.8 cc 010.jpg
 
Hallo Model Engine Friends,
Still a few other parts are revised at the Boll Aero engine for example a good fit Contra Piston which moves with a hard click to above when the piston goes upwards with some fuel between.
There's also a better compression lever mounted made from a tiny piece of steel plate.I did some refinements at he back plate and propeller screw which now can be mounted complete with propellor and propdriver.
I hope you like the pictures again which maybe will be following up by another couple of pictures when some new ideas are comming inside my head.

many greetings from modelmotor-Gerard-The Netherlands-Europe.

Boll Aero engine parts  and Steam Engine parts 001.jpg


Boll Aero engine parts  and Steam Engine parts 002.jpg


Boll Aero engine parts  and Steam Engine parts 006.jpg


Boll Aero engine parts  and Steam Engine parts 003.jpg


Boll Aero engine parts  and Steam Engine parts 004.jpg


Boll Aero engine parts  and Steam Engine parts 007.jpg


Boll Aero engine parts  and Steam Engine parts 012.jpg


Boll Aero engine parts  and Steam Engine parts 015.jpg
 
Hallo Model Engine Friends,
The continuation from the pleasure in making new parts for my Boll Aero 1.8 model diesel engine which was n't the succes i was hoping for seems to be an endless story and even so an endless picture show of making these parts which i like to share with you as my Model Engine Friends.
I hope you like my struggle with my machinery and aloy in HE15 quality special meant to make a new conrod from.

Many greetings from modelmotor-Gerard-The Netherlands-Europe.

001.jpg


002.jpg


006.jpg


007.jpg


008.jpg


009.jpg


010.jpg


011.jpg


012.jpg


013.jpg


014.jpg


015.jpg


016.jpg


017.jpg


036.jpg
 
Hallo Model Engine Friends,

The pictures will show you the finishing from the Home Made Conrod for my
Boll Aero 1.8 model diesel engine.
I hope that you like the work i did at my Conrod to get it in the right shape.

Many greetings from modelmotor-Gerard-The Netherlands-Europe.

038.jpg


039.jpg


040.jpg


041.jpg


042.jpg


026.jpg


Boll Aero 1.8 ccmodel engine parts remak 001.jpg


Boll Aero 1.8 ccmodel engine parts remak 002.jpg


Boll Aero 1.8 ccmodel engine parts remak 004.jpg


Boll Aero 1.8 ccmodel engine parts remak 005.jpg


Boll Aero 1.8 ccmodel engine parts remak 007.jpg


Boll Aero 1.8 ccmodel engine parts remak 008.jpg


Boll Aero 1.8 ccmodel engine parts remak 009.jpg
 

Latest posts

Back
Top