My first engine, a Hoglet

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

camm-1

Well-Known Member
Joined
Feb 15, 2012
Messages
109
Reaction score
58
Hi
I had a couple of ours tonight in the shop and begin with the flyweels.
Decided to mill them out ruffly first and so I could fasten them to the inside first in the lathe.
Its to small, and hope they will go intto the chuck with the outer jaws.
But..bullsh..it fails some millimeters and I tryed to turn the jaws of but they was to hard th_wtf1


hog9.jpg


hog11.jpg


hog12.jpg
 
That is a very nice start to this wonderful little Engine :bow:

Regards,

Will
 
That is going to be a neat engine. I'll be following along!
 
Hei Ove.
Nice start on the Hog.
Now that I see you in progress my first thought was: "Sh..t I want to build one more" ;D
Time will show. ::)
CS

 
Hi and thanks boys!!
Until now it have work good and I´m waiting for the castiron to the liners and som more.
To make the cylinders and it start to look somthing is the funniest!
Bård: make a few more. You now " She makes it, she takes it for a few dollars more"
Love Smokie!
However I can not get the brass ring ready in my lathe it to small unless I dont by a bigger chuck.
I will wait to we get power to our big Storebro at my work.
I have not got the first issue nr 10 that the plan was in yet and dont now what is in it about this engine but I now want to proceed with the crankshaft.
What is the best order in progress or how to say???
Regards
Ove :bow:
 
I like the start you have made on the hoglet. I have the plans and am getting the materials together so I can make one once I get the confidence up. I'll be watching this build :)
Pete
 
Just a note for anyone building this on a small lathe , instead of doing as Ove has done and using brass plate to make the flywheels, obtain a short length of hollow cast bronze and that way the outside, inside and one face can be machined by holding in a 4" chuck, swap it end for end and do the second flywheel. Then saw down the middle and just face off the saw cuts still holding buy the inside.

The bronze is also heavier than brass thats why its specified.

J
 
Hi!
Have got some time this wekend and finished one head :bow:
And the flywheels are ready but just notice I dont have a pic on them :

20120514_213559.jpg
 
Hey hey hey, Ove
Jælar. Nice work on the cyl.head ;), one up one to go.
Ps: call you on the end of the week.

Best Regards
CS
 
Thanks CS! That wast the funniest part do machine so far ;D
 
Today I got the second head finished :D
It went much faster this time about 3 ours and Im pleased about the result.
Now I have to make the cylinders so it get to look like a engine ;D


topp1.jpg


toppar2.jpg
 
Hi all of you metalfreaks ;)
I dont have much time now to this hobby this time of the year but
was all alone tonight and finished one liner and put it together a bit :)
But I have a problem.. the crankshaft dont line realy straigt true the crankhousing
because the housing sides are not square or how you say. Just a little but I
havnt find out yet how to solw it easy ???


hog15.jpg


hog14.jpg
 
Now my Hoggie start to take shape ;D ;D ;D
Finished the cylinders now to evenings.
Cast iron sleeves and alu fins.


Hoggencyl1.jpg


Hoggen cyl2.jpg
 
Wow, that is looking very nice. Thm:
 
Thanks for kindly words!
I have more pics by the building that Im been to
lazyto post but I will soon :)
 
Ove,
Have you made anymore progress to your Hoglet ?
Dave
 
Hi!
I have not done anything in the summer but started a little now.
I promis to get you pics later.

Have fun!
Ove
 
Hi all of you!
Continued building on my Hog this wekend and got conrods , valveseats , valvesteerings ready
and one valve to.
I also put in rollerbearings instead of bronze bushings in the crankhouse.
Prssed in 4mm long valveseats of brass.
Here are som pics but sorry if the dont come in order.
Ove.

klar ventil.jpg


lådan.jpg


sida lager.jpg


stake1.jpg


stake2.jpg


stake3.jpg


stake 6 vev.jpg


styrning1.jpg


styrning2.jpg


styrning press.jpg


styrningar.jpg


topp brotch.jpg


ventil såg.jpg


ventisäte press.jpg
 

Latest posts

Back
Top