Cleaning out all my engine kits

Help Support HMEM:

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
Hello to all, I have not been on here for a long time due to some health concerns.
I have been looking at the shelves with all my engine kits that I probably never get to and made the decision that I have to clean house.
I have a Root-Vandervoot 4hp vertical water cooled, partially machined, a 1912 GADE air cooled not touched.
Numerous other kits in cast iron and cast alum for steam and some other gas kits also.
If any of you members are interested, please contact me through this board for at odrog11250@aol.com, I do not have a complete list at this time as it is hard to compile at this time.
Gordo
 

kvom

Administrator
Staff member
Administrator
Global Moderator
Joined
Jun 4, 2008
Messages
3,184
Reaction score
594
I'd suggest posting your location.
 

LSEW

Well-Known Member
Joined
Jan 2, 2013
Messages
54
Reaction score
12
OK, so like KVOM said, tell us where you are, at least what country.
Next, It would be good to list your kits so we don't have top guess.
The next question is about what you are expecting to get for them.
That is the first question folks are going to ask.

So, that being said, I'm selling my extra kits too, but am looking for a
Bob Bromps Fairbanks "R" 2, 3, or 4 cyl version. Just a guess you may have it.

maury
 

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
Sorry to have dropped the ball and run off. I leave in Oakdale, Minnesota. I have a list of the stuff now and can email it to anyone interested as it is 1 and a half pages long and I don't want to plug up this forum. If anyone was interested in the GADE it was sold. email is at top.
 

e.picler

Edi from brazil
Joined
Jan 3, 2012
Messages
368
Reaction score
230
Location
Curitiba - Paraná - Brazil
Sorry to have dropped the ball and run off. I leave in Oakdale, Minnesota. I have a list of the stuff now and can email it to anyone interested as it is 1 and a half pages long and I don't want to plug up this forum. If anyone was interested in the GADE it was sold. email is at top.
Please, send me the list.
Tks,
Edi
 

H Pearce

Member
Joined
Sep 7, 2010
Messages
14
Reaction score
1
Hi,

Would you be able to email me the list please?

Thanks.


Sorry to have dropped the ball and run off. I leave in Oakdale, Minnesota. I have a list of the stuff now and can email it to anyone interested as it is 1 and a half pages long and I don't want to plug up this forum. If anyone was interested in the GADE it was sold. email is at top.
 

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
THIS IS WHAT IS LEFT AS OF 5-24-20




2. P.M. research model #1 steam engine Alum. casting set with plans. 110.00 plus shipping

4. D&M Model Engineering steam engine, cast iron vertical model 60-201 Lt Special with plans, 85.00 plus shipping.

6. Peterson Products 1 cylinder alum steam kit 5/8” bore, vertical. 35.00 plus shipping.

9. Pioneer Non-Compression Internal Combustion Engine by Rudy Kouhoupt, plans only with 2 VHS tapes and full set of plans 30.00 shipped.

12. P-M Research Inc. #3 Steam Mill Engine. Alum. Casting set with plans. I have two of these for sale, one is a #3 with straight spoke flywheel and a 3A with curved spooked flywheel 77.00 each shipped.

14. Quayle 16/16 H Model Steam Eng. Bar Stock engine kit from New Zealand. Horizontal cylinder with plans. 100.00 shipped.




I will be taking pictures today and putting them on my computer to send them out to those who want more info. I don’t want to put them on the board and take up space. You can email me for them at odrog11250@aol.com or call 612-889-9370.

Thanks Gordon
 
Last edited:

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
See above.
 
Last edited:

Cogsy

Well-Known Member
Staff member
Global Moderator
Joined
Jul 30, 2012
Messages
2,840
Reaction score
832
Location
Perth, Western Australia
I wish I could afford the Root-Vandervoort. I have one at the moment that I'm fixing up for its owner and it's a very nice model. It will make someone very happy as they're not being produced anymore and I don't think there's any plans to offer them in the future.
 

Jasonb

Project of the Month Winner!!!
Project of the Month Winner
Joined
Mar 30, 2008
Messages
2,421
Reaction score
431
Location
Surrey, UK
Yes the R&V makes a nice engine, just to temp someone to part with their cash here is one I made earlier

 

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
see above
 
Last edited:

mohavegun

Well-Known Member
Joined
Jan 15, 2018
Messages
52
Reaction score
14
Looking to buy a set of castings and drawings for an Elmer Wall "Wizard" two cylinder engine, anybody have such?
 

Gordo

Well-Known Member
HMEM Lifetime Supporter
Joined
May 3, 2009
Messages
46
Reaction score
6
Thank You to all who have either asked or bought my kits, I have sold them all.
This a great group!!!

Gordo
[/QUOTE]
 

coffeebean16

Member
Joined
Jan 1, 2011
Messages
16
Reaction score
3
Wanted to publicly thank Gordon for the engines. He was easy to do business with and understanding when I had an unexpected delay in the process. I’ll post the engines up as I get them done.
Dave
 

Latest posts

Top