Search results

Its been a while since I played with this engine. Today I will take it out and start it again

kind of fixed the solenoid issue but still not working right. Once I get time, will work on it. here is a video which demonstrate the hit and miss https://www.youtube.com/watch?v=2xBzJMYASYI

Yes, there is an electronic pump which will circulate the water for 20 secs when sum of RPM goes above 10,000. then the counter get reset to 0 and wait for the next total 10,000

EGG engine is completed and running. http://www.homemodelenginemachinist.com/showthread.php?p=253624#post253624

9/11/14 Got the solenoid working https://www.youtube.com/watch?v=Un0HZwI8pwg&list=UUL8gj_06zIsMRLY-U6zQItA This engine is called EGG Engine, which stands for Electronic Guided Governor which is a 4 cycle hit and miss, water cooled engine and is based on my own design. The bore and stroke for...

well reason for basic stamp 2 was it was sitting in my box doing nothing for the last few years. But won't spend the money to buy it just for this project.

Hello friends I am not sure what am I getting myself into. Must be the heat in Florida But EGG is going to be water cooled engine and the governor will be electronic using solenoid So here is the heart of the EGG. The micro controller will monitor the RPM, based on the nub level (0..4) which...

Hello all I am building a small .75” Bore x.75” stroke 4 cycle hit and miss engine. The Governor will be electronic on this engine. Meaning once RPM reaches ~2000 I will leave the exhaust open until RMP drops to XX or is better to keep the exhaust opened for SS seconds? So I need...

Neils, So sorry but lost you. Not sure what you are refering to? Borna

Niels, I was thinking about a long stroke, but due to some available metals on hand and some other variables I decided for square engine. Plus already have a long stroke engine, so wanted something different :) http://www.homemodelenginemachinist.com/f43/vertical-one-4-cycle-engine-completed-19963/

This project is officially started. First part, the frame is completed. Many other parts to follow Specification: Water cooled Single cylinder 4-cycle hit and miss engine Electronic water pump Govenor: EGG poppet intake valve Piston: Aluminum with cast iron ring Cylinder: 1040 steel Stroke...

This deserve to be the project of the month.

Thank you all. Today the engine Ran for 4 hours straight non-stop. Kept adding fuel every 15 mins :)

This is an excellent job, Maybe a newbie in engine building but for sure not a newbie in machining which is what it counts.

Electronically Guided Governor Engine Ok the name is little misleading thinking what the hell is an EGG engine. Good marketing strategy, but now that you are here. The other day I was cleaning my tool box and came across this little fellow. Its a small 5-volt push solenoid. I suddenly decided to...

I was planning to use a rollpin, but I think would be hard if you need to remove the flywheel from crankshaft. But I could be wrong. However I used 2 piece clamp on shaft-collars and holding very well after total of 2 hours run time. Borna

This engine by Jan looks so good. Once I saw it running in youtube, I said I had to make one. To make it more challenging for myself, I decided to make one that looks like his engine a little larger but using my own design. Borna

This looks awsome. As far as skills, what is the hardest part of this engine? How long it took you build this? Borna

Hello all, Vertical-One 1" bore x 1.5" stroke Flywheel, 5.5" cast iron Piston: Cast iron with cast iron ring Cylinder: Steel Ignition: CDI with Hall Sensor Timing: Ignition: 5 degree BTDC EO: 40 degree BBDC EC: 15 degree ATDC IO: 10 degree BTDC IC: 5 degree ABDC...

Good point Karsten. I never thought about it. :hDe: Now to Enginemaker, why are you saying that this is an exact duplicate someone else's engine? Can you refer me to a picture?