Search results

I am struggling with poor vision right now and I have not been able to find an answer to my question. Is this only for small engine/tools/books, or can members post other items? Specifically RC related. Thank you.

A little late, but I thought I would answer this question. This project was started 6 to 7 years ago and was going to be presented in a magazine. I do not remember why, but the drawings did not make it to publication. I worked with the gentleman who had the original engine/model engine to...

SOLD Thank you Steve for all your time and effort in making this work. Ernie Daniel

Reduced Price. $60.00 Sorry, due to health issues, and the low price, I can not travel the 50 mile radius as stated above. Even if you do not want these for yourself, for this price, you should be able to make a profit on re-selling these to someone who is looking for the original hard...

Reduced Price. I will accept any offer over $70.00. This price is only offered until August 6. I have three Dr. appointments (starting Aug 7th) that I can not miss and this will help pay my co-pays.

Lowered Price. $90.00 Need to sell as soon as possible. If you are traveling up/down interstate 5 in Oregon, Grants Pass is right on the freeway.

Please note that it may take a day or two for me to respond to any messages.

Reduced the price. $100.00

MODEL ENGINE BUILDER MAGAZINE Hard copies of issues 1 thru 27 Excellent condition $135.00 Please note that these can not be shipped. I can travel in a 50 mile radius of Grants Pass, OR if needed.

Hello, First, I am an Alibre fan and support the software whenever I can. I have used other software and my best experiences has, so far, been with Alibre. I started a project in the early 90's designing a one-third scale working model of a 1937 Norton motorcycle. The design was first...

I see the same thing here. This has been going on for me for approx 2 days.

Thank you again all of those who took the time to reply to my question. All of them made me realize that I need to be more descriptive in my writings and also that I need to write to the suggested audience.

Hello, I am hoping someone in the manufacturing industry has been presented with this problem before and can help me with the answer. On a manual lathe above center will be in an upward direction from the spindle center-line and below center will be in a downward direction from the spindle...

Hello, I have wanted to help with tips/machining methods in this forum but so far I have not been able too. This idea is something I have used in the past and just wanted to pass it along. This is geared more for the person who is just starting out in model making. I hope this is not too...

Here are the PDF’s as the png’s are a little hard to read.

Hello, On one of my Sherline Mills I have noticed that it can get out of square at times so this is something that I check frequently. This is a Model 2000 mill. (the 8 directional mill) I find that I don’t really have any problem with the X alignment but the Y can move at times. I have been...

Thanks again for all the suggestions. Looking at this design I can see where if it was not made right it could throw off the part. I do not know how critical the actual machining is or if I just got lucky. Anyway, I just thought I would show what I was trying to do. The pulley had to be...

Thank you to all who replied. After reading the above replies I did the following: 1. Changed the slope to 10 degrees 2. Cut all 10 degree slopes in one setting (so they would match up) 3. Extended the collet area to approx 1 inch (I knew this but was not thinking as is should when I drew this...

Hello, I am trying to help a friend who’s boss gave him a “little work at home”. I cannot be too specific about the part to be machined except this will be to perform second and third operations on a pulley. All the bores are from .5002 to .5050. I have seen a machinist use a similar expanding...

Hello, I only have a small area that I can call my own, so to maximize the space, this is what I came up with. The table and stand-alone stand (with the dial indicators on the bottom shelf) were made up from scrap 2x2’s from a cabinet shop. All of the table/stands are made so that I can move...