Recent content by reloader

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. R

    Hardinge Dividing head with stepper

    Hello Sid, I use the programm from KQuiggle. It works very well for me. best regards Edgar
  2. R

    Hardinge Dividing head with stepper

    Hallo Sid, good looking project! Which arduino program do you use? best regards Edgar
  3. R

    Arduino Rotary Table for Dummies

    Hallo, I finished my rotary table project today. Special thanks to kquiggle who gave me the support I needed. I decided to use annother keyboard. I do not like these membran switch bords. best regards Edgar
  4. R

    Arduino Rotary Table for Dummies

    Hello, the program is still working fine. The output of the Step Pin 2 is still looking strange. I have never seen such a signal duty cycle with AccelStepper. Is there any PWM regulation of Pin 2 in this program? best regards Edgar
  5. R

    Arduino Rotary Table for Dummies

    Hello, just loaded the sketch with AccelStepper. It runs smooth without any problems.🖕 So, special thanks to kquiggle for this sketch, I really like it. best regards Edgar
  6. R

    Arduino Rotary Table for Dummies

    Hello, I had to go back to the beginning of this thread to see, that kquiggle has two rotary table sketches. So I loaded the version Table_Control_2019_7.25. After making the setup, it works without any problems, but it has hard start and stops for the stepper. After uploading the sketch...
  7. R

    Arduino Rotary Table for Dummies

    Hallo, today I got the 4*20 LCD Display. During lunch, I connected the display and a Keypad switch to my Arduino uno an installed the original program of Bob. The keypad did not run as it should, so i changed the wiring as suggested. Now it works.👍 Later i will test the program with my rotary...
  8. R

    Very short programm for a rotary table

    Hello, thankes for your advice. I made some changes to this program and defined the steps to run as steppo. So I have only to change steppo to change the steps to run. I will check, if my program still runs without the <>. best regards Edgar
  9. R

    Very short programm for a rotary table

    Hello, as I told before, I am a bloody beginner. I bought an arduino kit from Elegoo. In this kit is a cheap IR remote sender and a IR receiver device. All the rotary table programs I have seen here are open loop programs. So you have to trust your strong stepper. But you can test the program...
  10. R

    Arduino Rotary Table for Dummies

    Hello, I had a look at all 21 pages and I found a lot of different programs. I would like to build a controller with 4*4 pad and the 4 row LCD display. I am little bit confused, where to find the latest version of Bruces program together with the wiring plan. best regards Edgar
  11. R

    Very short programm for a rotary table

    Hello, As I told before, I am very new to the Arduino project and I was very impressed by the high complex sketches of people that built an arduino controlled rotary table. I decided, that it would be nice to have a short program to run my table. Starting with accellstepper, I think, this is...
  12. R

    Interrupt Driven Rotary Table controller

    Hello Rod, I do not understand, what you mean with the changes in post#107? If I delete a comment, the program will not be changed. How does the arduino knows, what LCD shield is used? I could not see this in the program. Today I loaded the older version rotary 10. Also with this version, I...
  13. R

    Interrupt Driven Rotary Table controller

    Hello, attached you will find some photos of my 7 division run. You can see the first, the 5th, the 7th and the 9th division. Please have a look at the frequency. The signal comes direct from the step Pin. Any help is wellcome. best regards Edgar
  14. R

    Interrupt Driven Rotary Table controller

    Hello, i must say, that I am a little bit helpless. I installed the origin rotary 11, checked that the changes in the LCD library were done. Then set the Dir pin with the LCD shield at 2 and the step pin at 1. But the step pin 1 was not saved! Now I have the funny situation, that Dir Pin is 2...
  15. R

    Interrupt Driven Rotary Table controller

    Hello, I thougt about a new strategy to solve my problems. I will install the originial rotary 11 again with the driver pins 1 and 2. Then I will search, where this pins are on my strange AZ delivery LCD shield. It seems soo ,that the locations of pin 1 and 2 are complete different to other LCD...
Back
Top