Recent content by Art K

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

  1. Art K

    Ellery Single Cylinder 50cc Design & Build

    Looks good so far! Art
  2. Art K

    270 Offy

    Terry, I have been following along but haven't said much. I just wanted to say that in talking to guys that have built the Offy they know its time to shut it down when they see bubbles in the top coolant line. That is the sign its getting hot. I'm glad that you were able to do a compression test...
  3. Art K

    Werowance attempts Upshur Vertical Single

    Hey, congratulations on building a running engine! Its much easier to sort things out when it does run. Art
  4. Art K

    Werowance attempts Upshur Vertical Single

    What I have found on my Upshur after using 2 Perry carbs and the single jet carb in the drawings. The stock carb was fine but. If you ran it at a higher rpm you had to open up the jet, then close it to idle. A .198 Perry was to big, yes it ran but, if you opened the throttle to fast it would...
  5. Art K

    Werowance attempts Upshur Vertical Single

    Werowance, I must admit with work and other stuff going on I am only now getting caught up with your build. I have to say I am glad I did my cam as a one piece unit and not assemble it. In post 392 you have the print showing where the cam is to be located. My suggestion would be if you loctite...
  6. Art K

    270 Offy

    Reminds me of a pair of Weber carbs. Art
  7. Art K

    Werowance attempts Upshur Vertical Single

    When I originally made mine, I had no CAD or CNC mill and I made shims to center the crank. In my rebuild I did everything in cad to the center line of the case. Hopefully it will come out as expected, Dead center. I still haven't heard from my nephew about the computer rebuild for my mill. Art
  8. Art K

    Werowance attempts Upshur Vertical Single

    Well, that's not a pretty picture but presumably they all wiggle and bend where they aught to. Art
  9. Art K

    Rebuild time for my Upshur single

    Ok, I had grandiose plans to work on the rod over the holiday weekend. Turned on the switch that turns on and off the computer and pop. Talked to my nephew and ordered a new power supply in hopes that was all that was wrong with it. I think it'll be here in a few days, then I will find out. Art
  10. Art K

    Werowance attempts Upshur Vertical Single

    Hey, do what the doctors tell you to do and don't push it. Heal up fast! Art
  11. Art K

    1/4 scale V8, first project.

    Hey Steve, I think I can help with that, I've got a video from the 2019 Zanesville show. Art
  12. Art K

    Rebuild time for my Upshur single

    Steve, Thanks, It was a bit of work and experimenting to get a working program. I originally made a rectangle in Alibre roughly the width of the cam ran one pass ti clean up the surface. Then I posted it and added the 180 steps. When I realized it was going to take 17 seconds to rotate 2 degrees...
  13. Art K

    Werowance attempts Upshur Vertical Single

    I think you just have shop elves, they jump out and grab things out of midair and drop them in the most unlikely places.:) Art
  14. Art K

    Rebuild time for my Upshur single

    Hi everyone, After some problems I now have a new cam. I had the program written two weekends ago but, I had some problems with my mill and couldn't run it. I couldn't zero the Z axis on the mill. I had even run the program an inch above the part, dropped it down & had to shut it down before it...
  15. Art K

    270 Offy

    Terry, I have been lurking during this build. I have Ron's book as well and have much of the engine drawn up in Alibre. This process has taken me about 2 years. Before starting on this journey I had never done an assembly. There is so much about CAD I don't understand or forget by the time I use...
Top