Help with Rider Ericson casting

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Nikhil Bhale

Well-Known Member
Joined
Nov 15, 2019
Messages
147
Reaction score
136
Location
Vidharba, India
Hello

I bought casting kit for Rider Ericson hot air engine from Myers.
I need some help with them.
While machining the leg I made a boo boo. I tried to take a deeper cut and broke one of the leg. I was thinking about using 2 part epoxy to fix it. Is there any better way to fix it.

IMG_20220712_211140.jpg
One of the other casting is slightly bent. Can I unbend it by applying heat? Or will it be better if I machine it as it is.




IMG_20220718_121033.jpg
Regards Nikhil
 
Hello

I bought casting kit for Rider Ericson hot air engine from Myers.
I need some help with them.
While machining the leg I made a boo boo. I tried to take a deeper cut and broke one of the leg. I was thinking about using 2 part epoxy to fix it. Is there any better way to fix it.

View attachment 138562One of the other casting is slightly bent. Can I unbend it by applying heat? Or will it be better if I machine it as it is.




View attachment 138563Regards Nikhil
Is there a better way to fix it
Yes silver solder it
 
Use silver solder without problem. I did with the Stuart Steam engine block with fault measure of drill holes when I rebuild the non complete steamengine.
 
Bend cast iron is not common, measure first if it's enough material to work after the drawings. If not, heat up to glowing and bend straight carefully.
 
If that is the same engine I bought from Myers it is cast aluminum. Silver solder will not work. Good epoxy it the only choice. I would use JB Weld.
 
If that is the same engine I bought from Myers it is cast aluminum. Silver solder will not work. Good epoxy it the only choice. I would use JB Weld.

It was stupid, .. better to send the part that is incorrectly cast and get the new part. Contact your dealer.
 
Bend cast iron is not common, measure first if it's enough material to work after the drawings. If not, heat up to glowing and bend straight carefully.
This is an aluminium casting. I think some zinc is also added to it.
The drawings supplied by Myers leaves much to be desired. I am referring to the book Steam and Stirling engine to build part 1 for the drawings. But the scale is different.

Regards
Nikhil
 
It was stupid, .. better to send the part that is incorrectly cast and get the new part. Contact your dealer.
This is easier said than done. I live in India and ordered the castings directly from Myers website.
The shipping would be too expensive for me.

Regards
Nikhil
 
Hello

I bought casting kit for Rider Ericson hot air engine from Myers.
I need some help with them.
While machining the leg I made a boo boo. I tried to take a deeper cut and broke one of the leg. I was thinking about using 2 part epoxy to fix it. Is there any better way to fix it.

View attachment 138562One of the other casting is slightly bent. Can I unbend it by applying heat? Or will it be better if I machine it as it is.




View attachment 138563Regards Nikhil
Greetings,
If it were me, plan "A" would be to obtain two replacement castings. Plan "B" would be to have someone take a few minutes and re-attach the leg by TIG welding it. Then I would heat the other warped casting red-hot and carefully straighten it. If it is cast iron, it should straighten relatively easily considering how few degrees it needs to be bent. If this second casting is also aluminum, it probably can / should be straightened at room temperature.

I have straightened many overloaded cast iron "C" clamps while heating them to redness.

Good luck! Clark.
 
This is a difficult joint to bond with epoxy. Small area and long legs makes the cross section to length a non-viable joint. Fortunately there is a solution which usually works. Assuming the legs are straight or have been straightened then you need to insert a pin into the joint to give it strength and then use epoxy to hold the pin in place and act as a gap filler. .....or get a new casting!
Best of luck - let us know how you get on!
Mike
 

Latest posts

Back
Top